new product TSMP1138 www.vishay.com vishay semiconductors rev. 1.1, 08-jan-13 1 document number: 82484 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ir sensor module for remote control systems mechanical data pinning: 1 = gnd, 2 = carrier out, 3 = v s features ? photo detector and preamplifier in one package ? ac coupled response from 30 khz to 55 khz, all data formats ? if the ir singal strength is less then 300 mw/m2 (distance more than 0.6 m with a typical ir remote control), the frequency range is up to 60 khz ? improved shielding against electrical field disturbance ? agc to suppress ambient noise ? high sensitivity, long receiving range ? supply voltage: 2.5 v to 5.5 v ? carrier out signal for ir repeater applications ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 description the TSMP1138 is a miniaturized sensor for receiving the modulated signal of infrared remote control systems. a pin diode and preamplifier are asse mbled on a lead frame, the epoxy package is designed as an ir filter. the modulated output signal, carrier out, can be used for repeater applications and code learning applications. this component has not been qualified according to automotive specifications. block diagram application circuit 94 8691 1 2 3 parts table carrier frequency code learning applications 38 khz TSMP1138 33 k 1 3 2 v s out compa- gnd pass agc input pin band rator control circuit 16833_11 v o c1 4.7 f r1 100 TSMP1138 supply voltage + 5 v gnd 0 v r3 680 r4 3 tsal6400 33 k recommended circuit for best sensitivity of the tsop9xx38 in repeater applications. it limits the output voltage swing v o to about 0.7 v in order to avoid internal coupling.
new product TSMP1138 www.vishay.com vishay semiconductors rev. 1.1, 08-jan-13 2 document number: 82484 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? stresses beyond those listed under absolute maximum ratings ma y cause permanent damage to the device. this is a stress ratin g only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute maximum rating co nditions for extended periods may affect the device reliability. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - output function fig. 2 - frequency dependence of sensitivity absolute maximum ratings parameter test condition symbol value unit supply voltage (pin 3) v s - 0.3 to + 6 v supply current (pin 3) i s 5ma output voltage (pin 2) v o - 0.3 to 5.5 v voltage at output to supply v s - v o - 0.3 to (v s + 0.3) v output current (pin 2) i o 5ma junction temperature t j 100 c storage temperature range t stg - 25 to + 85 c operating temperature range t amb - 25 to + 85 c power consumption t amb 85 c p tot 10 mw soldering temperature t 10 s, 1 mm from case t sd 260 c electrical and optiocal characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit supply current (pin 3) e v = 0, v s = 5 v i sd 0.55 0.7 0.9 ma e v = 40 klx, sunlight i sh 0.8 ma supply voltage v s 2.5 5.5 v transmission distance e v = 0, test signal see fig. 1, ir diode tsal6200, i f = 400 ma d30m output voltage low (pin 2) i osl = 0.5 ma, e e = 0.7 mw/m 2 , test signal see fig. 1 v osl 100 mv minimum irradiance less than 5 missing or 5 additional sub carrier pulses related to one burst e e min. 0.5 1 mw/m 2 maximum irradiance less than 5 missing or 5 additional sub carrier pulses related to one burst e e max. 30 w/m 2 directivity angle of half transmission distance ? 1/2 55 deg v o v oh v ol tpi 6 carrier cycles is recommended for optimum function t e e t pi - burst length optical test signal: ir diode tsal6200, i f = 0.25 a, n = 15 carrier pulses per burst, f = 38 khz, burst repetition time: 3 ms t the number of carrier- out-pulses might not be exactly same as the number of carrier cycles in t pi (input burst) 21648 0 0.5 1 1.5 2 2.5 3 3.5 30 35 40 45 50 55 60 f o - carrier frequency (khz) e e min. - detection threshold (mw/m2) 21772
new product TSMP1138 www.vishay.com vishay semiconductors rev. 1.1, 08-jan-13 3 document number: 82484 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - relative spectral sensitivity vs. wavelength fig. 4 - horizontal directivity ? x fig. 5 - vertical directivity ? y 750 850 950 1050 0 0.2 0.4 0.6 0.8 1.2 s ( ) rel - relative spectral sensitivity - wavelength (nm) 1150 94 8408 1.0 94 8153 0 0.2 0.4 0.6 0.2 0.4 0.6 - 30 d rel - relative transmission distance 010 - 10 - 20 20 - 40 x y 94 8152 010 - 10 - 20 20 - 30 - 40 0 0.2 0.4 0.6 0.2 0.4 0.6 d rel - relative transmission distance
new product TSMP1138 www.vishay.com vishay semiconductors rev. 1.1, 08-jan-13 4 document number: 82484 this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters 96 12116-1 center of sensitive area area not plane (9.2) 0.8 max. 2.54 nom. 0.4 + 0.10 - 0.05 1.4 0.3 4 0.3 5.8 0.3 10 0.3 12.5 0.4 0.5 + 0.15 - 0.05 0.65 + 0.10 - 0.15 30.6 0.5 drawing-no.: 6.550-5095.01-4 issue: xx; 20.05.09 specifications according to din technical drawings 3 x 2.54 = 7.62 nom. r 2.75
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
